Can the Brace Be Swithched on a Galil Ace 308 Pistol

In my previous posts, I covered a chip of the history of the Galil Ace, did two posts about the differences betwixt the Ace and an AKM that I observed (click here for the first and here for the 2d) and at present that leads upwards to me making a few tweaks of my own to my 7.62×51 Ace pistol.

Moved to a SB Tactical SBA4 Brace

My Ace came with a SB Tactical SOB brace mounted on a proprietary IWI tube with a very heavy swivel. While the SOB is rugged, it is not adjustable so I installed and SB Tactical SBA4 brace. Seriously, the SBA4 is the most rugged brace I have constitute yet.

The SOB4 caryatid is what comes with GAP51SB pistols. Palmetto had a great deal on this model and that's why I bought it. If I could have found the pistol model without a brace cheaper, I would take done that.

The SBA4 caryatid is beefier and more rigid that previous braces. The bottom e dges do not flop around similar they do on the SOB and SBA3 braces. The FSM-AR adapter is between the tube and the receiver.

At present some may wonder why I didn't but file for a short barreled rifle (SBR) taxation postage and run a normal stock. I may very well exercise this in the future only I didn't desire to bargain with it correct now. Both PSA and Brownells have the brace available.

The Ace design allows for very easy changing of a rear cake by simply driving out one roll pin. The cake can the be lifted direct out and whatever you want installed in its place.

The Ace is resting on a dark-green demote block and I used a roll pivot punch to tap out that single pin. That's all y'all demand to do and then the rear plate of the receiver that holds the hinge, or anything else for that matter, will elevator correct out.

With the pivot removed, information technology literally lifts out. Find how the "plate" or "block" sits in a groove and that'due south what provide the bulk of the strength. The scroll pivot is just stopping vertical travel and is more enough.

Since the SBA4 is ATF approved, I opted for a modular adapter cake from KNS Precision going to an Ace Limited (owned past Doublestar and not IWI) folding M4 adapter – the FSM-AR. Note, if y'all install a folder, buy 1 with the boss – the raised oval shape. It will fit into the groove in the KNS Precision adapter and make for a very solid connectedness.

This is the external face of the KNS Precision adapter. The groove is where the boss from the FSM-AR adapter will sit to limit movement. I'd recommend always getting adapters with the bosses unless you intentionally do non want them. The two screw holes allow for variations in mounting.

This is the back side of the KNS adapter. The one roll pivot goes through one of the grooves to concord it in place. Information technology is very nicely done – kudos to KNS Precision.

The KNS adapter merely slides right in and is secured by the curlicue pin.

This is the Ace Express (owned past Doublestar and not IWI) FSM-AR adapter. You tin can see the oval boss on the left part of the folder. This gets flipped over and screwed into the KNS adapter. Also, oil the swivel at some point before you close it. Sometimes they can exist a deport to actuate when dry — personal experience talking at that place. Also, apply blue Loctite on all screws or they will shoot loose.

Special note – the charging handle for my Ace pistol is on the left side. In my case, I was non worried well-nigh operating when folded. If you want to fire with the stock folded, you must go with a right side folding mechanism. If I had it to do over, I would have used a correct-side folder simply I merely used what I had in this instance to cut cost plus I don't program on folding it much.

Here's the Ace folder open to the left and the caryatid assembly does interfere with the charging handle. If you lot want a weapon that will operate with the brace folded, and then become with a unit that folds to the right.

The SBA4 comes with a Mil-Spec receiver extension (buffer tube) and I used a generic castle nut that I had in my tool box along with an terminate plate that has hoops to connect a sling.

The SBA4 comes with a Mil-Spec receiver extension/buffer tube. You will need to supply your own castle nut .

I merely use my Magpul wrench at present for installing castle nuts as it enables a very positive/sure connection. I've done my fair share of scratching stuff with tools that used older methods and the MagPul is the way to get. I likewise used an automatic center dial to stake the nut.

For dealing with castle nuts, you only can't beat the Magpul wrench. I don't utilize the philharmonic wrench below it any more because I have scratched a ton of tubes accidentally with it.

The Magpul armorer's wrench is bachelor from both Brownells and PSA. Again, I highly recommend this wrench over others that I have used.

All in all, it was a very direct forward swap and allows for some aligning now. In case you are wondering, the SBA4 is very beefy. I do not like the SBA3 as the stop is soft and and ears that become around the shooter'southward forearm simply kind of curve and flop around. The SBA4 is very well done.

I definitely volition SBR it at some bespeak down the road simply am happy with what I have for now.

Installed a RS Regulate GAR-9M-N Handguard

I was not fond of the original handguards and was pretty sure I would similar the GAR-9M-N handguard from RS Regulate based on photos that Scot Hoskinson had posted. Let me tell yous, information technology is a huge improvement. Start off, it'due south way longer and 2d information technology uses a M-LOK zipper method for accessories and then y'all don't have unnecessary track bulking up the girth like you practice with the originals.

This is the RS Regulate GAR-9M-N handguard for Ace pistols. It's machining and stop are excellent. Installation was very like shooting fish in a barrel.

Scot Hoskinson, the owner of RS Regulate, has put together a existent nice installation guide with plenty of illustrations. The one affair I'll tell you lot is that the two original handguard screws from IWI have threadlocker on them.

Just behind the oral cavity of the gas tube & front sight block is the mounting point that holds the ii screws that retain the original Ace handguards. They do have threadlocker on them so warm them up to brand removal easier.

I used a ane/4″ ratchet with a 4mm allen scrap and the retaining spiral on each side came right out. Notation, yous will see ii rivets on each side – one rivet head is visible betwixt the wrench handle and the bit. Yous don't need to practise anything to those. You just demand to remove the 2 screws. You tin can see ane of the in a higher place just forward of the bit.

You can heat them upward and make them easier to loosen, use a 1/4″ ratchet with a 4mm allen/hex head to pause the screws free or, what I did, was a bit of both. With the gas tube off and out of the way, yous tin run across where the two screws mountain on the barrel. I heated that up and backed them out with the ratchet pretty easily.

In one case the screws are removed, slide the handguard forward slightly and pull the rear down. It will come right off.

From there, yous basically pull the stock handguard downwards nose first and pull forward. So, follow Scot's instructions. Yous will need to pay attention and install a pocket-size spacer betwixt the barrel mounting indicate and the handguard when yous install the new screws. I applied bluish Loc-tite and torqued them down to 25 in/lbs per Scot'south instructions. You lot also have to install one long spiral at the rear that yous'll want to use the blueish Loc-tite and torque to 25 in/lbs also.

The RS!Regulate comes with the three screws, 2 spacers and an allen wrench. I applied medium-strenght Blue Loctite and used my Vortex Optics torque driver to tighten the screws to 25 in/lbs.

The installation instructions where spot on and I did non encounter whatever surprises at all. The unit bolted right up with no fitting needed.

The fitment is actually superb. Here the runway is sliding over the rear block and will be secured later with the long spiral that squeezes the rails's walls together further locking it in identify.

I similar the RS!Regulate unit far, far more than than the original. It'southward longer and it fits my hand way better in terms of girth.

This is a slick handguard – the fit and terminate are superb. I've come to expect that from all RS!Regulate products. Scot'due south created another great product in my honest opinion. His AK scope mounts are the best hands down in case yous aren't familiar with them.

Opted For a Vortex Razor AMG UH-i Optic and 3x Magnifier

I figure this volition be a close in weapon – certainly within 200 yards probably – and will figure that out when I get it to the range. With that in mind, putting a high power optic on it but does not make a lot of sense just I also wanted magnification just in case so I checked out what Vortex Optics had to offer.

I've now used a boat load of their red dots and scopes on all kinds of firearms including 12 gauges, .l Beowulf and .338 Lapua. They're solidly built, skillful glass and back by a no-nonsense warranty. And so they are my go-to for optics and have been for several years. Yes, I do actually have to purchase them and no, they do non pay me to say that.

At whatever rate, I'd been eyeing the Razor AMG UH-1 for a while. Now that is a mouthful and I detect a lot of guys simply refer to it has the "Huey" due to the UH-i helicopter. Information technology's a true holographic sight which ways a laser image (a hologram) is projected into the viewing window. The benefit of this is that regardless of the bending you look through the lens at, if the dot is on the target, it's going to hit in that location.

The Razor AMG UH-1 or "Huey" mounts easily with its quick release lever and is ruggedly congenital.

It has a big viewing window that makes sight conquering very fast.

The controls are well laid out and like shooting fish in a barrel to employ.

Bombardment life is somewhere around one,500 hours and there are a lot of variables that tin influence that including the brightness of the reticle (there are fourteen levels), whether you are using a CR123A battery or a rechargeable LFP123A. Notation, Vortex found that recoil kills the basic rechargable RCR123 batteries in 2-300 rounds. They stopped testing the LFP123A at ten,000 rounds and it was still working. I'chiliad using the supplied CR123A still at this betoken and will probable use Surefire CR123A batteries going forward as I go along them in stock for lights.

In curt, the Huey is very slick and it's getting slap-up reviews. I've been a long-time red dot fan and the UH-ane is my favorite at this point.

To go a better view at 100-200 yards, what I did was to pair the Huey sight with the Vortex V3XM Micro 3x magnifier. What this does is requite me the ability to install, remove or fifty-fifty swing the installed optic out of the manner when I demand or don't need the target to be magnified 3x.

Some assembly was required and I practical medium-strength Blue Loctite to the screws.

Hither's the Vortex Micro 3x magnifier paired with the Huey.

The V3XM is small, calorie-free, has a quick release lever as well, merely like the Huey, and pairs very nicely with it.

Magpul PMags and Drums

The vii.62×51 Ace uses Magpul'southward vii.62×51 PMags. You lot tin get them in a number of sizes as well equally a drum if you lot actually want to rock and roll. I bought some 20s, 25s and one of the D50 drums. I've not tested the pistol notwithstanding but wait it will work bully with all of them. Note, both PSA and Gun Mag Warehouse have a variety of mags and drums that volition fit.

Here's the end result with the SBA4 caryatid, RS!Regulate rails and Vortex Eyes philharmonic.

Summary

The pistol really turned out slick. It balances well and ought to exist a blast. Now just to find some fourth dimension to go to the range before it actually gets common cold 🙂 Here are some photos for you:

---

Notation, I take to buy all of my parts – nothing here was paid for past sponsors, etc. I do make a pocket-size amount if you click on an advert and buy something just that is it. Yous're getting my real opinion on stuff.

If you observe this mail useful, please share the link on Facebook, with your friends, etc. Your back up is much appreciated and if you accept any feedback, please email me at info@roninsgrips.com. Please note that for links to other websites, I may be paid via an affiliate program such as Avantlink, Bear on, Amazon and eBay.

---

berubetherhold.blogspot.com

Source: https://blog.roninsgrips.com/customizing-an-iwi-galil-ace-pistol-installing-a-rs-regulate-handguard-sba4-brace-vortex-optics/

Share this post